|
Freud C400 6-1/8-by-11/16-by-1/8-Inch Jointer Knives, 3-Pack
|
MSRP: $35.42
Your Price: $22.09
Savings: $ 13.33 ( 38% )
Shipping: Usually ships in 24 hours
Manufacturer: Freud
Prices subject to change. Please verify price during checkout.
|
|
Freud C400 6-1/8-by-11/16-by-1/8-Inch Jointer Knives, 3-Pack Features
|
Produces the smoothest cut
Precision-machined for best results; pre-ground to a razor sharp edge
Made from premium high-speed steel stock
3-pack of jointer knives
Manufacturer's limited lifetime warranty
|
|
|
|
|
|
|
|
|
Additional Freud C400 6-1/8-by-11/16-by-1/8-Inch Jointer Knives, 3-Pack Information
|
The Freud Difference
Freud manufactures some of the most innovative, technologically advanced woodworking tools and accessories in the world. To ensure that the highest quality products meet the toughest design standards, Freud owns and operates six manufacturing facilities in Western Europe. Freud is one of the few manufacturers of woodworking tools in the world that produces its own MicroGrain carbide with titanium, called TiCo -- a combination of titanium and cobalt. Freud develops different types of carbide for each application to maximize the cutting life and performance of the tool; and Freud also operates one of the most modern product development research centers in Europe. By overseeing the entire manufacturing process from start to finish, Freud guarantees some of the highest quality, most advanced products in the industry. About these Replacement Knives
These Freud 6-1/8-inch replacement jointer knives are designed for use with the Ryobi AP10. They're pre-ground to a razor sharp edge in order to produce the smoothest cut possible. Precision-machined for best results, these knives are made from premium high-speed steel stock for a keen edge and long life. Key Tech Specs:
6-1/8 inches long 11/16-inch wide 1/8-inch thick Warranty
This 3-pack of knives is covered by Freud's limited lifetime warranty.
|
|
|
What Customers Say About Freud C400 6-1/8-by-11/16-by-1/8-Inch Jointer Knives, 3-Pack:
|
|
If you want basically the same blades that came with your Ridgid, these work fine. I used these on my Ridgid JP0610 Jointer and they are at least as good as the blades that came with the unit. They are not an upgrade, but may very well be the most cost effective solution. They already have little nicks in them, which is about what the stock blades did too. For the price they are very reasonable. I bought a couple sets to make sure I don't run out again. As always they were shipped promptly and arrived on time and un damaged.
Should have sent them back but I needed them immediately. Bought these knive to replace the ones in my ridgid jointer. right out of the box they had a curl on them and needed to be honed. After only an hour or so of use they are completely curled over and so dull they chatter the wood. Very dissapointed in the product, spend the money and get a good set if you plan on using them at all.
Have not had a chance to try them yet but I have Freud blades in my table saw and router and they hold up great so I would expect the same from these. Needed replacements for my ridgid jointer. I have learned not to be too hard on jointer blades. These look identical and are exactly the same dementions. They are razor sharp and mount in there perfectly. Don't cut deeper than you have to and check your blades often. I didn't bother to check them till I was getting bad cuts and was amazed at how badly I had worn them down.
Drop in replacement of the factory knives that come with the Rigid 6 1/8 Jointer and good quality as expected from Freud.
I decided to take a chance on these blades for $17.11 from Amazon. It was covered in rust and the motor was missing. A friend of mine brought over a Sears 6 1/8 jointer he found in the garbage. The blades are a perfect match to the old blades. I decided to rebuild it at almost the cost of a new one. Sears wanted $36.99 for the blades plus shipping and tax. If you have a Sears 6 1/8 Jointer Model#113206931, these blades will fit, but always measure the size of the old blades to be sure. Since Sears made several different models of jointers.
|
|
 |
|
|
